Parallelism OOOOOOomOOmooOoooooOOOOOOOOOoOOoOOOoOOoOOOoOOOOoooO Straightness OOO~OOOOOOOOOOOO~~OOOOOOOOOOOOOOOOOOO~~OOOOOOOO~OOįlatness OOOOoOOo*oOOoOOoOOOoOOOoOOOOOOOOOOOoOOOOOOOoOOOOOOOOOO General OOOoOOoOOoOoOoOeOOOOOOoOOOoooOOOOOOOOoOOo~oOOOOOOOoOooO Testing ~OO~OOOOOO~OOOOOOOO~OOOOOOOOOOOOOOOOOOOOOO~OO~OOOO~O~OO Indications on drawings l OOOO~OOOOOOOO~OOOOOOOOO~O~~~OOOOO~OOOO Straightness, flatness and parallelbm tolerances l OO~OOOOOOOOO Tolerances for angular dimensions l ~OOOO~OOOOOOOOOOOOOO~OOO~~OO Tolerances for 1 inear dimensions l OoOOOOOOOOOOOOOOooOoOOOOoO.* General tolerances l OOOoOOOOOOOOOOOOOOOOOOOOOOOOOooooOOmOOoooo. Normatlve references OOOOomOOOOOooOoOOoOOoOOOoOOOOOoOoOOOOO****ĭefinitions OOOOOOoOOOOoOOoOOOOoOoOOOOOoO~OOOOOOOooOooOOOOoooo* Scope oo*oooooooooooOooooOOOoOoooooOOooOOoeOOoOoOOOooOOOoOO**** International Organization for Standardization Case postale 56 l CH-1211 Geneve 20 l Switzerland Internet central x.400 c=ch a=400net p=iso o=isocs s=centralįoreword *.ooooooo*ooooooomoooooooooooooooooooooo*oOoeoooooooooooooo Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Standard IS0 13920 was prepared by the European Committee for Standardization (CEN) in collaboration with IS0 Technical Committee TC 44, Welding and allied processes, Subcommittee SC IO, Unification of requirements in the field of metal welding, in accordance with the Agreement on technical cooperation between IS0 and CEN (Vienna Agreement).Īll rights reserved. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.ĭraft International Standards adopted by the technical committees are circulated to the member bodies for voting. International organizations, governmental and non- governmental, in liaison with ISO, also take part in the work. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. The work of preparing International Standards is normally carried out through IS0 technical committees. IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). Soudage - Tolkrances g&Wales relatives aux constructions soudhes - Dimensions des longueurs et angles - Formes et positions Welding - General tolerances for welded constructions - Dimensions for lengths and angles - Shape and position WEB LINKSCheck if this document is current
#Iso 2768 mk pdf download full#
RUN-OUT Tolerance class H 0.1 K 0.2 L 0.Conditions of use: Click here for full conditions of Licence PERPENDICULARITY Ranges in nominal lengths in mm up to 100 over 100 up to 300 over 300 up to 1000 over 1000 up to 3000 Tolerance class H 0.2 0.3 0.4 0.5 K 0.4 0.6 0.8 0.8 L 0.6 1 1.5 2 Tolerance class designation (description)f (fine) 0.2 0.5 1.0 m (middle) 0.2 0.5 1.0 c (coarse) 0.4 1.0 2.0 v (very coarse) 0.4 1.0 2.0ĪNGULAR DIMENSIONS Permissible deviations in degrees and minutes for ranges in nominal lengths up to 10 over 10 up to 50 over 50 up to 120 over 120 up to 400 over 400 Permissible deviations in mm for ranges in nominal lengths 0.5 up to 3 over 3 up to 6 over 6 Permissible deviations in mm for ranges in nominal lengths 0.5 up to 3 over 3 up to 6 over 6 up to 30 over 30 up to 120 over 120 up to 400 over 400 up to 1000 over 1000 up to 2000 over 2000 up to 4000
#Iso 2768 mk pdf download iso#
GENERAL TOLERANCES FOR LINEAR AND ANGULAR DIMENSIONS (DIN ISO 2768 T1)LINEAR DIMENSIONS: Variations on dimensions without tolerance values are according to "DIN ISO 2768- mk". General Tolerances to DIN ISO 2768 The latest DIN standard sheet version applies to all parts made to DIN standards.